|
Heineken BT10001 BeerTender Tubes, 10 Count | 
 enlarge | Brand: BeerTender
Category: Kitchen
Buy New: $11.99
New (7) from $11.95
Rating:  16 reviews
Sales Rank: 169
Shipping Weight (lbs): 0.4
Dimensions (in): 15.4 x 10.7 x 1.9
MPN: 106822
Model: BT10001
UPC: 072890004055
EAN: 0072890004055
ASIN: B0013DTA0E
Release Date: August 15, 2007
Availability: Usually ships in 24 hours
Tell A Friend
Add to Wishlist
Add to Wedding Registry
Add to Baby Registry
| |
| Features:
| | 10-count package of BeerTender tubes | | | Connects BeerTender and Heineken or Heineken Premium Light DraughtKeg | | | Fresh, new tube required for each new DraughtKeg | | | Simple installation; step-by-step instructions right on the bag | | | Measures 15-2/5 by 10-2/3 by 1-8/9 inches |
|
| Similar Items:
|
| Editorial Reviews:
Product Description
This Set of 10 Krups BeerTender Tubes will keep your beer fresh and delicious. Using a new tube with each new keg is recommended to ensure the perfect flavor every time. Secure a perfect fit between the Krups BeerTender home beer-tap system and a Heineken or Heineken Premium Light DraughtKeg thanks to this 10-count package of BeerTender tubes. Each new DraughtKeg requires a fresh tube and installation's a snap. Step-by-step instructions are available right on the bag, which measures 15-2/5 by 10-2/3 by 1-8/9 inches.
|
| Customer Reviews: Read 11 more reviews...
 Reusable If You're Careful September 28, 2008
BO (southwestern VA)
2 out of 2 found this review helpful
The BeerTender recommends using a new tube for each mini-keg, and at about a dollar each that's not a big deal. However, if you have run out of tubes, or just want to be thrify, they can easily be reused at least a couple times. Here's how:
o Put the empty mini-keg in a sink.
o With the tube's spout pointing toward the drain, push the two white barrel fittings together. This manually operates the tap to relieve pressure in the mini-keg.
o Wait a few seconds for all the foam to drain out.
o Use a screwdriver or butter knife to remove the top part of the tap. There are three tabs on this gray cover piece; pry back one or two to lift it off.
o Remove the part still attached to the mini-keg by pushing back the tabs holding it to the top of the keg. Use a screwdriver or butter knife on the inside part of the tap - accessible with the cover removed - to release these tabs.
o Thoroughly rinse the tap, tube, and spout. With the barrel connectors still pushed together, run a stream of water into the spout and it should drain through the tube and out the small holes in the tap.
o Snap the cover piece back onto the tap with the larger hose cut-out aligned with the tube.
o Pull the barrel connectors apart to manually close the tap to make it ready it for the next mini-keg. Be sure the whole thing is very clean, especially if not using immediately.
I've used one tap three or four times, and it still works fine (no leaks, similar pour). I suspect they recommend using a new one every time because it can be messy removing it from the mini-key and the potential for it to get moldy if not cleaned.
Don't forget the part about relieving the residual pressure, or you will probably have a beer geyser when the gray cover is removed.
Beertender tubes June 19, 2008
Beer Lover (Seattle WA)
1 out of 1 found this review helpful
Works perfectly with the Heineken Draughtkegs. Its a great way to get Heineken Light on Draught!
Can't beat the convenience July 8, 2008
M. Smith (Tamarac, FL)
1 out of 1 found this review helpful
While it's a bit of a pain (and cost) to be tied to an item like this that needs replacing, what can beat the convenience of having beer on tap at home? At least the kegs are pretty reasonable!
Excellent quality and speedy delivery overseas. June 2, 2008
Phillip Hernandez (RAF Lakenheath)
2 out of 3 found this review helpful
My beertender tubes arrived quickly. Before my Beertender which still hasn't arrived. I am completely satisfied with the quality of the product and the speedy delivery. I would recommend using Amazon.com for your Beertender needs!
Excellent August 31, 2008
HHuf (NC, USA)
Don't hesitate to order this product here...it arrived on time and in good condition. works perfectly with the Krupps Beertender. Have not had a
defective one so far. installs and fits perfectly in the dispenser. The price is right and it saves having to have additional gear to clean the
machine. only thing left to clean now is the tip and thats it.
|
|
|
|
| |
